During roofing operations, workers use hot tar, torches, hot kettles, or plastic welding machines that can expose themselves to heat, flammable materials, burns hazards, and overexertion. These exposures can lead to serious injuries and heat illnesses. Training in proper work practices, using proper protective equipment, and planning for emergency situations are keys components in complying with provisions of the California construction safety orders: (Section 1510 – Safety Instructions for Employees, Section 1524 – Water Supply, Section 1730 – Roof Hazards, and Section 3395 – Heat Illness Prevention).
Use proper personal protective equipment
- During work, wear light-colored, flame-resistant clothing with long sleeves and cuffless long pants to protect you from heat and burns.
- Collars and hoods cowls protect your face, neck, and ears.
- Wear a hard hat, safety boots with a non-slip sole and heel, and leather or heat-resistant gloves.
- Don’t tuck your pants into your boots.
- Face shields, side-shielded safety glasses, or goggles protect your eyes.
- A respirator protects your lungs from fume exposures.
- For hot tar roofing, wear a face shield when you add tar chunks or kegs to the tanker truck or kettle.
Know the conditions of your work environment
- Check the weather before you work.
- Work in high temperatures and humidity can lead to heat illness.
- Ensure that cool water is available nearby.
- When possible, try to work in a cooling breeze and keep fumes away from workers.
- Do the heaviest work in shaded areas and the coolest part of the day.
- Stay hydrated by drinking small amounts of water frequently.
- Remove your protective equipment when you take breaks.
Plan for emergency situations
- Make an emergency plan.
- Know the roof escape routes.
- Set up communication between the roof crew, building, and ground workers.
- Know the local emergency numbers for fire and medical services.
- Know first aid for heat illness and severe burns.
Use safe work practices and fire precautions
- To prevent fires, clear flammable material, gases and/or liquids off the roof.
- Mark and protect permanent building fixtures, gas, and electrical lines.
- Seal off air intakes and roof openings to keep fumes and flame out of the building.
- Have fire extinguishers available.
- Pumping the hot tar to a hot lugger tank on the roof and then to a mop cart is safest.
- Hot tar from hand-carried buckets can splash and burn you.
- Don’t carry hot tar buckets up a ladder; use a hoist line.
- When you carry a hot tar bucket, walk cautiously to avoid slips and falls.
- Keep buckets and carts covered until you use or dump the materials.
- Hand-held or walk-behind roof torches can exceed 2000°F.
- Don’t torch directly onto building materials, flashing, or voids in the roof.
- Be careful on heavy slopes; walk-behinds can roll away or tip over.
- Don’t pull a walk-behind backward on roofs that exceed a 4:12 slope.
- When you set the torch down, always turn it off and set it upright on its legs.
- Don’t hang a torch over the roof edge.
Follow manufacturer’s safe guidelines when using torches and plastic welding machines
- To turn the torch off, turn off the propane fuel tank first, then allow the gas in the line to burn off.
- Stop work 2-3 hours before you leave the job to prevent hot spots or smoldering fires.
- Welding machines to apply plastic roof membranes reach 1100°F and use up to 220 volts of electricity.
- To prevent electric shock, use ground fault circuit interrupters (GFCI) and avoid rain or wet areas.
- Don’t touch grounded objects such as pipes or scaffolding while operating the equipment.
- Don’t overheat plastic membranes, they can emit toxic compounds.
The above evaluations and/or recommendations are for general guidance only and should not be relied upon for legal compliance purposes. They are based solely on the information provided to us and relate only to those conditions specifically discussed. We do not make any warranty, expressed or implied, that your workplace is safe or healthful or that it complies with all laws, regulations or standards.